Hardwood
Engineered hardwood
Luxury vinyl plank
Laminate
Porcelain tile
Carpet
Shaw
Mohawk
COREtec
PergoFree in-home measure and written estimate: Shaw, Mohawk, COREtec and Pergo lines compared on your own rooms, with carpet, tile, vinyl plank, laminate and hardwood laid out side by side
Get your free estimateStyles & brands we work with
- Hardwood
- Engineered hardwood
- Luxury vinyl plank
- Laminate
- Porcelain tile
- Carpet
- Shaw
- Mohawk
- COREtec
- Pergo
See the difference
Before
After
Before
After
Before
AfterHow Much Does Hardwood Floor Refinishing Cost in Summerlin?
Hardwood floor refinishing in Summerlin typically costs $1,800 to $5,000 for a 500 to 800 square foot project, and that’s the installed price with sanding, staining and finish work included. A single room usually lands at the lower end, while a full main floor with heavy sanding and a custom stain pushes toward the top. Our technicians have up to 9 years of experience, and every estimate is written, itemized and free.
If you’re deciding whether to cover an original wood floor or bring it back, the math is worth a closer look. Refinishing keeps the wood you already have in the house instead of sending it to a dumpster and starting over. It’s also a job most carpet-and-tile shops don’t want to touch, since sanding and finishing demand a different set of hands, different equipment and a careful sequence from grit to grit. We offer it as one of our three core services, so it’s handled with the same attention we bring to flooring installation Summerlin homeowners count on for tile and carpet.
Summerlin’s housing stock matters here. A lot of the homes in the master plan were built with solid oak or engineered wood in the main living areas, and after enough years of desert sun coming through west-facing windows, that finish starts to look chalky, thin at the thresholds and dull in the traffic lanes. Refinishing is the fix. Replacing the floor is usually not, unless the boards themselves are damaged. We answer the phone 24/7, and fast dispatch runs 7am to 7pm, Sunday through Friday.
Hardwood Floor Refinishing Cost Breakdown (2026)
Here’s what the pieces of a refinishing job usually run in Summerlin, priced as part of a typical 500 to 800 square foot project. These are estimated ranges, not per-square-foot quotes. The written estimate you get after we see the floor sets the final price.
| Line Item | Typical Estimated Range |
|---|---|
| Sanding and prep (full floor, dust control) | $400 – $900 |
| Stain application (single color, oil-based) | $300 – $700 |
| Finish coats (three coats, clear or matte) | $500 – $1,200 |
| Screen and recoat (light refresh, no deep sanding) | $300 – $650 |
| Board replacement and patching (per area) | $150 – $600 |
| Stair treads and risers (if in scope) | $50 – $100 per tread |
| Full project, 500 – 800 sq ft | $1,800 – $5,000 |
The whole-job range of $1,800 to $5,000 is what you should anchor on. Where a project lands inside that band comes down to four things: how much old finish has to come off, whether a stain is involved or the floor stays natural, how many square feet are actually in scope, and whether any boards need replacing before the sanding starts. A straightforward recoat of a lightly worn floor is a different job than a full sand-down on 30-year-old oak with cupped edges. Add a custom-mixed stain and you’re at the upper end. The written estimate spells out each of those pieces separately so you can see what you’re paying for and decide what you actually need.
Refinishing starts from about $3 per square foot for the finishing work itself, though the total depends on the product, the room and the condition of the wood. For comparison, new hardwood installation runs $4,500 to $12,000, which is why most homeowners who have a refinishable floor choose to refinish. A note on pricing: you’ll sometimes see $1 a square foot advertised online. That’s usually a single coat and no sanding, and it’s rarely what a 20-year-old Summerlin floor actually needs.
What Affects Hardwood Floor Refinishing Pricing in Summerlin
Every refinishing job is a little different, and the price moves with the floor. Here are the factors that matter most, in the order they usually show up at the estimate visit.
- Type and thickness of the existing wood. Solid oak and most engineered floors can often be sanded, but a thin engineered wear layer may only tolerate a light screen and recoat. We check board thickness and wear layer at the estimate before quoting a full sand. This is the single biggest price lever, and it’s the reason we don’t give firm numbers over the phone.
- Number of finish coats. A three-coat finish is standard for a floor that sees daily traffic. Two coats cost less, but on a living room floor that takes desert sun and foot traffic all day, the extra coat earns its money back in time between refinished floors.
- Stain versus natural. Natural clear finish is the simplest and the least expensive. A stain adds a step, adds drying time between application and finish, and if you want a custom color, that’s a test-and-approve process before the whole floor is coated. A gray or driftwood-toned stain that reads well against Summerlin’s warm interior palettes takes a bit more work than a standard warm brown.
- Furniture and room access. Refinishing means emptying the room. Floors that are accessible, clear and ready on the scheduled day move faster than rooms still full of furniture. Moving heavy pieces and clearing baseboards before we arrive saves you labor charges on the estimate.
- Board repair and patch work. Pet stains, water-damaged boards near a sink or a sliding door, and cracked or splintered planks all need to be swapped before sanding. Matching new boards to old is the tricky part, and it can’t always be perfect. Expect this to be a separate line on the estimate.
- Floor condition and cupping. A floor that has cupped or crowned from past moisture takes more passes to flatten. That’s more time and more sanding discs. If we see cupping at the estimate, we’ll tell you what it means for the price and whether the moisture issue needs to be addressed before any finish goes down.
Summerlin’s climate plays a role that’s easy to miss. The dry desert air and strong sun coming through west and south windows can dry a finish faster than in more humid parts of the country, and we adjust application sequences and dry times accordingly. Homes here also tend to have larger open-plan living areas, which means more contiguous square footage in a single sanding pass. That’s usually efficient on a per-square-foot basis, but it makes the initial setup and dust control more involved. The written estimate reflects the real room, not a generic average.
Should You Refinish or Replace Your Hardwood?
For most Summerlin homeowners with a sound wood floor, refinishing is the smarter spend. It protects original wood that’s already fitted to the house, and it runs roughly a third of what full replacement costs. Replacing makes sense when boards are deeply damaged, the wear layer is too thin to sand again, or the floor has cupped and shifted beyond what sanding can correct. If you’re considering new floors over the top, we’d steer you toward a tile or carpet conversation before a replacement conversation, since those are the two other categories we work in and both are a strong option for rooms where wood just isn’t the right choice.
One more point in refinishing’s favor: it’s a repair to the house, not a new product selection. The floor was specified for that room when the house was built, and it still works there. Bringing it back to life is often what owners of original Summerlin homes want, and the “refinish before you replace” instinct is usually right.
What’s Included in a Summerlin Hardwood Refinishing Estimate
A good estimate should spell out the scope line by line, not just give one lump number. When you get ours, you should see the sanding steps, the number of finish coats, any stain application and test patch, board replacement costs if needed, and the stair work if stairs are part of the job. We include cleanup and dust control in the scope, because a refinish that leaves sanding dust in a furnace filter isn’t finished. The price you see is the price of the job as scoped. If the scope changes, the price changes, and we talk through it before work starts.
How to Save on Hardwood Floor Refinishing
There’s no way to make refinishing cheap and still get a floor that holds up. But there are real ways to keep a project in the lower part of the range without cutting corners on the work itself.
- Get a screen and recoat instead of a full sanding if your floor qualifies. If the finish is dull but structurally intact and there’s no bare wood showing, a light screen and recoat refreshes the look for $300 to $650. We’ll tell you honestly at the estimate whether your floor is a recoat candidate or needs a full sand.
- Stay with a natural clear finish. Skipping the stain takes a line off the estimate and shortens the schedule. Most wood floors in Summerlin look great with a clear matte or satin finish.
- Move the furniture yourself. Clearing the room before we arrive is labor you don’t have to pay for. It’s a small thing, but it comes off the total.
- Bundle adjacent rooms into one job. A full-floor sand-down is more efficient than four separate room-by-room visits, since setup happens once. If you’re already doing the living room, adding the hallway or an adjoining dining space often makes sense financially.
- Address small repairs early. A loose or stained board caught at the estimate is a small line item. Caught after the finish goes down, it means sanding again.
- Get the estimate in writing, and get it free. Call (844) 320-7082 for a free estimate. We answer 24/7, and fast dispatch runs 7am to 7pm, Sunday through Friday.
What we’d avoid: cutting the finish down to two coats on a floor you intend to keep for years, or accepting a low bid that doesn’t include board repair. Both come back as a cost later. Refinishing is a job where the cheap version is usually the expensive version two years down the road.
Why Choose a Specialist for Hardwood Refinishing in Summerlin
Hardwood refinishing is a labor-intensive specialty. It involves reading the wood, choosing the right grit sequence, controlling dust in the home, testing a stain before committing, and knowing when to stop sanding. Most carpet-and-tile installers either outsource it or skip it entirely. That’s why we offer it as one of three core services: carpet, tile and hardwood refinishing, all under one contractor.
That trio of categories matters more than it sounds. The person advising you on refinishing the hallway is the same specialist who can specify carpet for the bedroom and a Daltile tile for the bathroom. That means your whole-home project is planned with an eye to how the floors flow together instead of getting handled in fragments. Our technicians have up to 9 years of experience with the craft, and we speak fluently about the products we install, from Shaw and Mohawk to COREtec, Karndean, Pergo, LifeProof, Mannington, Armstrong and Daltile. Nine brands, one conversation.
The refinishing side of what we do brings something the retail side can’t: we install floors, so we know what holds up. That knowledge helps when you’re deciding whether a floor is worth sanding back or whether a new floor makes more sense for a room. When you need to talk through a whole-home plan, the Summerlin flooring work we handle covers carpet, tile and refinishing together.
Two safety notes before you plan around refinishing. First, sanding equipment is heavy and the dust and finish fumes in a closed-up house need real ventilation planning, which is why we handle dust control as part of the job rather than as an afterthought. Second, if the floor turns out to be too thin to sand, we stop and tell you before we damage it. That’s a call we make at the estimate, not mid-job. For the dangerous parts of old homes, like a badly wired outlet feeding a floor lamp or gas lines near a renovation zone, always bring in a qualified electrician or gas professional; refinishing a floor is safe to schedule, but it doesn’t touch those systems.
FAQs – Hardwood Floor Refinishing Cost
How much does it cost to refinish hardwood floors in Summerlin?
Refinishing hardwood floors in Summerlin typically costs $1,800 to $5,000 for a 500 to 800 square foot project, including sanding, stain and finish. Finishing work starts from about $3 per square foot, but the final number depends on the floor’s condition, stain choice and room access. Call (844) 320-7082 for an exact quote; estimates are free.
Is it cheaper to refinish or replace hardwood floors in Summerlin?
Refinishing is almost always cheaper, typically $1,800 to $5,000 versus $4,500 to $12,000 for new hardwood installation in the Summerlin market. Replacement only makes sense when the wear layer is too thin to sand or the boards are damaged beyond repair. We check that at the estimate visit and tell you which one your floor needs. Call (844) 320-7082 to book a free visit.
Can you refinish a floor that has cupped or water-damaged boards?
Sometimes, but it depends on the extent of the damage and the thickness of the wood. Cupped edges and water-stained boards can often be sanded out or replaced, but a floor that has shifted or has a wear layer too thin to sand again may need partial replacement. We inspect at the estimate before quoting, and the written estimate sets the final price. Call (844) 320-7082 to schedule the inspection.
How long does hardwood refinishing take in Summerlin?
A typical 500 to 800 square foot project takes several days from sanding to final coat and cure, since each finish coat needs time to dry before the next step. The schedule is confirmed in the written estimate and depends on the number of coats, stain application, and the home’s conditions. Call (844) 320-7082 to plan a timeline; estimates are free.
Can you come today for a hardwood refinishing estimate?
Same-day estimates are often possible. We answer the phone 24/7, and fast dispatch runs 7am to 7pm, Sunday through Friday. Call (844) 320-7082 and we’ll find the closest opening for your free estimate.
Pricing reflects the Summerlin market as of 2026. Flooring Installation Summerlin offers free estimates – call (844) 320-7082.
Written by the team at Flooring Installation Summerlin.
What Our Customers Say
"Laminate in the family room and the hallway. They left a gap along the walls and covered it with new quarter round, and the floor has not buckled or creaked."
- Megan Doyle"He measured every room at the estimate and gave me the number on paper that same day. The number on the paper was the number I paid."
- Allison Norris"Staggered the plank ends properly so there is no stair-step pattern across the room, and the last row along the wall is not a thin sliver."
- Daniela Rodriguez